Switching Power,Inc- Switching Power Supplies-Hot Swap Power Supplies


	SNS-5600S Air Cooled. 5600 Watt, 270Volt/20.7Amp, Radar Transmitter Power Supply. 5600 Watts in 6.8"x8.13"x15.00" Size! 3 Phase 220V/60Hz and 380V/50Hz Input with Active power Factor Correction (Greater Than 0.99) Meets MIL-STD-1399, Section 300A (Type I) for the Voltage Ranges Specified Input Current THD not Exceeding 4%. Patent Pending Topological Approach Resulting in Cancellation of all Harmonic Power Line Frequency on the Output Ripple Without the need for additional large output LC filter. True Hot Swap with Floating ELCON Mini-Drawer Connector. N+1 Redundant with Internal Oring Diodes. Active Zero Wire Current Share Allowing for Redundant Modules to Share With in 10% of Each Other. Output Test Points on Front Panel LED Display for Output, Temp., Over Current and Fan Status Ruggedized Mechanical Design Meeting MIL-STD-810F, Method 514.5, Category 24, Procedure 1. SNS5600S Data Sheet. CPCI-250Q-P-47 300 Watts in 3Ux8HP (two slot)x160mm. Standard PCI Voltages 5V/50A, 3.3V/50A, +12V/6A, -12V/2A. PFC, N+1 redundant. With Oring diodes. Wide AC input range. Get complete details CPCI-250Q-P-47 Data Sheet. CPCI-250 IEC/FCC Conducted Emmisions Data. I2C Implementation Details. MILSTD704E- 115VAC/400HZ Increased energy storage for full load 70msec ride-thru. Available on CPCI-250/350/600 series. NEW! 600 Watt CPCI, 6Ux8HP Two Slot x160mm Unit. 600 Watt Data Sheet. CPCI-600 600 Watt I2C Bus-Data Sheet: CPCI-600-I2C-Data-Sheet	Water Cooled. LC-2000SFEATURES: Liquid Cooled 60/40 Ethylene Glycol-Water Mix coolant with attached Cold Plate. Operating Temperature: -40C to +85C. 2000 Watts in 11.81"x 12.40"x 4.72" Size! 3 Phase input 480V/60Hz. +28VDC/70A Output. LED display for Input/Output status. Certified to meet: High Temperature per MIL-STD-810F, Method 501.4 Procedure I and II Low Temperature per MIL-STD-810F, Method 502.4 Procedure I and II Humidity per MIL-STD-810F, Method 507.4 Pressure Altitude per MIL-STD-810F, Method 500.4 Procedure I up to 40,000ft Non-operational Pressure Altitude per MIL-STD-810F, Method 500.4 Procedure II up to 10,000ft operational Fungus per MIL-STD-810F, Method 508.4 Sand and Dust per MIL-STD-810F, Method 510.4 Procedures I,II and III Operational Salt Fog per MIL-STD-810F, Method 509.4 Vibration per MIL-STD-810F, Method 514.5 Category 6, procedure I composite wheeled, and US highway truck Shock: +/-15g for 11ms, half sine, each direction, all 3 axes Bench Handling: MIL-STD-810F, Method 516.5, Procedure VI. EMI meets: RS103 (Army Ground) RE102(Navy Limits) CE102 CS101 (Army Ground) CS114 (Army Ground) CS115 (Army Ground) CS116 (Army Ground) LC-2000S Data Sheet. LMCO-1366-SYS AN/TPS-59/FPS-117. 4 bay rack assembly with 1,400 Watts of N +1 redundant output power. All outputs floating to provide low output ripple and noise.Redundant single phase inputs per MIL_STD-1399. Sub-Rack designed to be rack mountable horizontally or vertically. Easy input and output connections via standard D-Sub connectors and bus bar arrangement. LEDS on each front panel indicate power supply status and status signals. Integral circuit breakers on each plugin module. Designed with the latest COTS technology to rediuce risk and cost. Overtemp,overload, overvoltage and short cuircuit protection. Hot swap plug-in modules for fast and simple serviceability. Certified to Mil-STD's 1399,810,830,461/CE102/RE102/RS103 /CS101/CS114 and including operation after Mil-STd-810F Method 509.4 Salt Fog. TPS-59 Data Sheet.	ITT-15000S-450 Radar Modultor Supply. 400-450 Volt Output at 37.5 Amps.17000 Watts Peak Power. Operating Temperature: 0 to 55 degrees C at 10,000ft altitude. Continuous 15000 Watts in 7.7" x 18.25"x22.00" Size. 3 Phase input 400V/47-63Hz. 400-450VDC adjustable, with 37.5A Output. LED display for Input, Output, Fuse, Temperature, Over Current, Over Voltage status. Ruggedized Mechanical Design to Withstand Harsh Environmental Conditions. RS-485 serial interface with RS-232 protocol. ITT-15000S Data Sheet. GAT-50W Conduction Cooled. Low Profile 5.0" x 4.25" x 0.85" Size. Operational Temperature -40 to 100 degrees C. Remote Sense Output Designed to meet the following specifications: High Temperature per MIL-STD-810F, Method 501.4 Procedure I and II Low Temperature per MIL-STD-810F, Method 502.4 Procedure I and II Humidity per MIL-STD-810F, Method 507.4(Non Operational) Pressure Altitude per MIL-STD-810F, Method 500.4 Procedure I up to 40,000ft Non-operational Pressure Altitude per MIL-STD-810F, Method 500.4 Procedure II up to 10,000ft operational Fungus per MIL-STD-810F, Method 508.4 Sand and Dust per MIL-STD-810F, Method 510.4 Procedures I, II and III Salt Fog per MIL-STD-810F, Method 509.4 Vibration per MIL-STD-810F, Method 514.5 Category 6, procedure I composite wheeled, and US highway truck Shock: +/-15g for 11ms, half sine, each direction, all 3 axes Bench Handling: MIL-STD-810F, Method 516.5, Procedure VI. GAT-50 Data Sheet. GAT-50 Inprocess.